How is everyone doing, its been awhile since ive been on so i had do make a new name. (Old one Jo7Gle). You all have really helped me out in the past so im back.
I have 2 alpine type r subs in a slot ported box. Im lookin to replace my Fusion 2000w mono block with a alpine amp but i want the best for these subs. Or just work with what i got. I want to have all my componets speakers change out to alpine also sometime I was lookin at doing all type r. I have a factory boss right now.
And im looking to get the Alpine IVA-W205 Double din head unit if anyone have any insite on it that would help to.
Replies (6)
kirchatndftbl on 02/2/2009 22:15:57
what model are your type r's?????
10s,12s,15s???
(2+2) or (4+4) voic coil configuration???
UNCVLZD on 02/4/2009 15:59:02
Sry they are 12s with (4+4)
UNCVLZD on 02/4/2009 16:01:13
I have them hooked up to the amp with a 1ohm load
swez on 02/4/2009 18:23:32
Welcome back Jo7!
Do you know the RMS output of this Fusion amp @ 1 ohm loads?
The model # of this Fusion amp would be helpful. Got a link?
Swez
UNCVLZD on 02/5/2009 15:50:36
Here is some info.
model: PP-AM20001
Maximum Power: 2000 Watts
RMS Power Output: 465 Watts RMS x 1 Channel @ 4 Ohms
750 Watts RMS x 1 Channel @ 2 Ohms
1150 Watts RMS x 1 Channel @ 1 Ohm
Frequency Response: 10Hz - 250Hz
Low-pass Crossover: 40Hz - 160Hz
the thing is that I was offerd some money for my amp and i want to have all alpine for when my car is ready for show so im debating on keeping it or take the money and go all alpine. whats my best choice....
swez on 02/5/2009 18:49:10
Problem here is that Alpine does not make a 1 ohm stable amp. You'd have to buy two MRP-M650's or MRP-M500's to get the job done. (1 sub per amp)
Both will be harder to find as they are older models. The Alpine PDX-1.600 will get the job done too, but this amp is expensive, not as reliable and you'll need a pair of them.
Swez
I have 2 alpine type r subs in a slot ported box. Im lookin to replace my Fusion 2000w mono block with a alpine amp but i want the best for these subs. Or just work with what i got. I want to have all my componets speakers change out to alpine also sometime I was lookin at doing all type r. I have a factory boss right now.
And im looking to get the Alpine IVA-W205 Double din head unit if anyone have any insite on it that would help to.
Replies (6)
kirchatndftbl on 02/2/2009 22:15:57
what model are your type r's?????
10s,12s,15s???
(2+2) or (4+4) voic coil configuration???
UNCVLZD on 02/4/2009 15:59:02
Sry they are 12s with (4+4)
UNCVLZD on 02/4/2009 16:01:13
I have them hooked up to the amp with a 1ohm load
swez on 02/4/2009 18:23:32
Welcome back Jo7!
Do you know the RMS output of this Fusion amp @ 1 ohm loads?
The model # of this Fusion amp would be helpful. Got a link?
Swez
UNCVLZD on 02/5/2009 15:50:36
Here is some info.
model: PP-AM20001
Maximum Power: 2000 Watts
RMS Power Output: 465 Watts RMS x 1 Channel @ 4 Ohms
750 Watts RMS x 1 Channel @ 2 Ohms
1150 Watts RMS x 1 Channel @ 1 Ohm
Frequency Response: 10Hz - 250Hz
Low-pass Crossover: 40Hz - 160Hz
the thing is that I was offerd some money for my amp and i want to have all alpine for when my car is ready for show so im debating on keeping it or take the money and go all alpine. whats my best choice....
swez on 02/5/2009 18:49:10
Problem here is that Alpine does not make a 1 ohm stable amp. You'd have to buy two MRP-M650's or MRP-M500's to get the job done. (1 sub per amp)
Both will be harder to find as they are older models. The Alpine PDX-1.600 will get the job done too, but this amp is expensive, not as reliable and you'll need a pair of them.
Swez
Copyright ClubKnowledge 2009 * All Rights Reserved
