i have 2 10" audiobahn aw1051t
10" High Performance Subwoofer
45 OZ. Strontium Magnet
2" 4 Layer Black Aluminum Voice Coil
300W RMS Power Handling Per Sub
600W RMS Power Handling Per Pair!
30Hz - 1kHz Freq. Response
91dB Efficiency
Bumped & Vented Polished T-Yoke
Poly Coated 2 Layer Non Pressed Paper Cone
Lug Lock Terminals
Dual 4Ù Voice Coils Per Sub
1Ù or 2Ù or 4Ù or 2Ù Stereo Operation
Rubber Gasket & Magnet Mesh Cover
i am wondering if this amp will push these subs
crunch v2600
V-Drive Blue Anodized Inverted Heat Sink Design
Dual VU Metering System with Acrylic Lens
Mesh Grille Ventilation Design
Chrome Heat Sink Cover
PWM Mosfet Power Supply
Fully Bridgeable Design
Ultra-Drive High Speed Mosfet Output Devices
Class AB Operation
On Board Tru-Spec Capacitors
Premium Hand Wound Torrid
Separate Bass & Treble Controls 0 to 12 dB Variable
Bass/Treble On/Off Switch
HP/LP/Flat Select Switch
High Pass from 10 Hz to 2.5 KHz Adjustable Crossover
Subsonic Filter
Low Pass from 40 Hz to 4 KHz Adjustable Crossover
Gold plated RCA Line Input
Gold plated RCA Line Outputs for Amplifier Daisy Chaining
Internal Protection – Thermal, Short Circuit, Overload Circuitry
Red Protection LED
Green “On” LED
300w X 2 @ 4 Ohms
400w X 2 @ 2 Ohms
800w X 1 @ 4 Ohms
i know crunch isnt the best amp in the world but this is what i can afford and i have had good experience with crunch amps i also know that they are overated on rms wattage so this is why i want to go with 800 watt amp
im going to wire the subs into a 4 ohm load
was wondering if i could just use one wire terminal on the sub box that im building
Replies (5)
Relax_The_Mind on 12/16/2003 21:09:43
yes
cplkittle on 12/16/2003 21:16:21
I think it will work fine, I have 2 12's (same series) and my kenwood 600w amp pushes them pretty damn hard. I would wire each speaker in series to 8 ohm, then together in parallel at 4 ohm to get the 800w. I think you will be happy with the results.
One wire terminal is fine, what kind of box is it?
also be careful when hooking up the DVCs, I fried one not too long ago because the little red dot was on the negative side of the voice coil terminal, and I didn't notice the small + and - stamp on the bottom of the terminal.
nck59 on 12/17/2003 08:41:43
well im building the box for my 96 s10 reg cab
13hx51wx4tdx8.5bd should give me about 1.565 airspace which these subs need .75 to 1.00
also do u think i might need polyfill with as big as the box is going to be
nck59 on 12/17/2003 08:44:19
oh ya it is sealed guess that helps to know lol
cplkittle on 12/17/2003 09:36:20
polyfill will help reduce backwaves and standing waves which degrade the sound quality.
Your Audiobahn speaker manual should have polyfill recommendations along with size requirements.
10" High Performance Subwoofer
45 OZ. Strontium Magnet
2" 4 Layer Black Aluminum Voice Coil
300W RMS Power Handling Per Sub
600W RMS Power Handling Per Pair!
30Hz - 1kHz Freq. Response
91dB Efficiency
Bumped & Vented Polished T-Yoke
Poly Coated 2 Layer Non Pressed Paper Cone
Lug Lock Terminals
Dual 4Ù Voice Coils Per Sub
1Ù or 2Ù or 4Ù or 2Ù Stereo Operation
Rubber Gasket & Magnet Mesh Cover
i am wondering if this amp will push these subs
crunch v2600
V-Drive Blue Anodized Inverted Heat Sink Design
Dual VU Metering System with Acrylic Lens
Mesh Grille Ventilation Design
Chrome Heat Sink Cover
PWM Mosfet Power Supply
Fully Bridgeable Design
Ultra-Drive High Speed Mosfet Output Devices
Class AB Operation
On Board Tru-Spec Capacitors
Premium Hand Wound Torrid
Separate Bass & Treble Controls 0 to 12 dB Variable
Bass/Treble On/Off Switch
HP/LP/Flat Select Switch
High Pass from 10 Hz to 2.5 KHz Adjustable Crossover
Subsonic Filter
Low Pass from 40 Hz to 4 KHz Adjustable Crossover
Gold plated RCA Line Input
Gold plated RCA Line Outputs for Amplifier Daisy Chaining
Internal Protection – Thermal, Short Circuit, Overload Circuitry
Red Protection LED
Green “On” LED
300w X 2 @ 4 Ohms
400w X 2 @ 2 Ohms
800w X 1 @ 4 Ohms
i know crunch isnt the best amp in the world but this is what i can afford and i have had good experience with crunch amps i also know that they are overated on rms wattage so this is why i want to go with 800 watt amp
im going to wire the subs into a 4 ohm load
was wondering if i could just use one wire terminal on the sub box that im building
Replies (5)
Relax_The_Mind on 12/16/2003 21:09:43
yes
cplkittle on 12/16/2003 21:16:21
I think it will work fine, I have 2 12's (same series) and my kenwood 600w amp pushes them pretty damn hard. I would wire each speaker in series to 8 ohm, then together in parallel at 4 ohm to get the 800w. I think you will be happy with the results.
One wire terminal is fine, what kind of box is it?
also be careful when hooking up the DVCs, I fried one not too long ago because the little red dot was on the negative side of the voice coil terminal, and I didn't notice the small + and - stamp on the bottom of the terminal.
nck59 on 12/17/2003 08:41:43
well im building the box for my 96 s10 reg cab
13hx51wx4tdx8.5bd should give me about 1.565 airspace which these subs need .75 to 1.00
also do u think i might need polyfill with as big as the box is going to be
nck59 on 12/17/2003 08:44:19
oh ya it is sealed guess that helps to know lol
cplkittle on 12/17/2003 09:36:20
polyfill will help reduce backwaves and standing waves which degrade the sound quality.
Your Audiobahn speaker manual should have polyfill recommendations along with size requirements.
Copyright ClubKnowledge 2009 * All Rights Reserved
